Planet Audio ADE-3400v3 Bedienungsanleitung

Wired / Wireless ADSL 2/2+ Router ADE-3400v3 / ADE-4400v3 / ADW-4401v4 User's Manual 1

Front Panel LED definition LED State Description ON When the router is powered on and in ready state. Red The devise is being turned on and bootin

Front Panel of ADE-4400v3 Front Panel LED definition LED State Description Green When the router is powered on and in ready state. Red The devise

defaults, keep the device powered on and push a paper clip into the hole. Press down the button over 5 seconds and then release. Power Power connector

Front Panel of ADW-4401v4 Front Panel LED definition LED State Description Green When the router is powered on and in ready state Red The devise

Rear Panel Port and Button Definition Connector Description POWER Button The power button is for turn on or turns off the router. Reset The reset but

2. Installation This chapter offers information about installing your router. If you are not familiar with the hardware or software parameters present

Figure 2 ADE-4400 / ADW-4401 connection diagram If do not need to connect to the splitter, z Connect the modem to wall jack with a telephone cable.

3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain

Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2.

Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration

Copyright Copyright© 2008 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed

3. Web Configuration Management Determine your connection settings Before you configure the router, you need to know the connection information suppli

Once you have powered on ADE-3400v3 / ADE-4400v3 / ADW-4401v4, system will boot up and connect to DSLAM automatically. In login dialog, enter “admin”

3.1.2 LAN Status You can see the LAN IP address, Mask, DHCP status, MAC and DHCP Client Table in this screen. 3.1.3 WLAN Status (ADW-4401 only) You c

3.1.4 WAN Status You can see the VPI/VCI, Encapsulation type, Protocol, WAN IP address, Gateway and DNS information in this screen. 3.1.5 Port Mappi

3.1.6 Statistic You can see the Statistic information in this screen. It includes the Traffic and DSL statistic. Traffic Statistic Screen The screen s

3.1.7 ARP Table You can see the ARP information in this screen. Click the Refresh button to refresh the information. 25

3.2 Wizard You can use "Wizard" to setup the router as follows, and the router will connect to the Internet via ADSL line. Step 1. Click &q

Step 3. Select the WAN IP type; select the WAN IP setting provided by your ISP. Step 4. Enter the user name and password that your ISP has provid

Step 5. Click "Next" to setup your LAN IP and DHCP Server setting. Step 6. Enter the Finish to save settings and reboot the device or cli

3.3 LAN The LAN setup includes two parts – LAN Interface and DHCP Settings. 3.3.1 LAN Interface Settings There are the IP settings of the LAN Interf

Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled

3.3.2 DHCP Server Settings Enable the DHCP Server if you are using this device as a DHCP server. This page lists the IP address pools available to hos

Enter the MAC address and the IP address that you wish to assign in the fields. Click the “Assign IP” button to add it in the MAC-Base Assignment Tab

3.4 WLAN (For ADW-4401 only) Click “WLAN” and it will open out the Sub-Menu. It includes the “Basic Settings”, “Security”, “Advanced Settings”, “Acces

Send Rate: Select the Wireless Data Rate that you want to use. Radio Power: 10%, 25%, 50%, 80%, 100%. Note: Please Commit/Reboot if you want to make t

Following is a description of the different options: 1. Key Length: Select 64-bit WEP or 128-bit WEP to use data encryption. 2. Key Format: Selec

Pre-shared Key Format: Select the Passphrase or Hax format. Pre-shared Key: Enter the pre-shared key for WPA. Client stations must use the same key in

Beacon Interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1024. A beacon is a packet bro

3.4.5 WDS (Wireless Distribution System) Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do

3.5 WAN 3.5.1 WAN Interface ADSL 2/2+ Router provide 8 PVCs with different channel mode. You can select the Bridge / MER / PPPoE / PPPoA mode for yo

PPPoE / PPPoA Mode Select this option if your ISP requires you to use a PPPoE / PPPoA connection. This option is typically used for DSL service. Pleas

Table of Contents 1. INTRODUCTION ...

1. Open the WEB page at “WAN Æ WAN Interface”. 2. Select the Channel Mode to “1483 MER”. Set the value of VPI / VCI and select the Encapsulation mo

3.5.2 ATM Settings The page is for ATM PVCs’ QoS mode setting. The device supports 4 QoS mode — UBR / CBR /rt-VBR / nrt-VBR. You can click the “ATM Se

SCR: Sustained Cell Rate (SCR) is the mean cell rate of a bursty, on-off traffic source that can be sent at the peak rate, and a parameter for burst-t

3.6 Advance You can configure different advanced services in this part. It includes DNS, Firewall, Virtual Server, Routing, IP QoS, Anti-DoS, Port Map

DDNS In this screen, you can modify the Dynamic DNS settings. The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname

3.6.2 Firewall Firewall is an advance feature used to deny or allow traffic from passing through the device. ADSL router support some firewall related

Rule Action: Select the Deny or Allow for your rules. Direction: Select the Outgoing or Incoming. Protocol: Set protocol type to be blocked or allowed

Default Action: Specify default filtering rule action to be either Deny or Allow if no other rules can be applied. Click the “Apply Changes” to apply

3.6.2.3 URL Block This page is used to configure the Blocked FQDN (Such as tw.yahoo.com) and filtered keyword. Here you can add / delete FQDN and filt

3.6.3 Virtual Server The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make v

3.6.2 Firewall...

3.6.3.2 DMZ A DMZ (Demilitarized Zone) allows a single computer on your LAN to expose ALL of its ports to the Internet. Enter the IP address of that c

3.6.4 Routing You have two ways to manage the device’s routing information. It includes RIP and Static Route. 3.6.4.1 RIP Enable the RIP if you are u

3.6.4.2 Static Route This page is used to configure the routing information. Here you can add / delete IP routes. Click “Enable” to enable the Static

3.6.5 IP QoS Entries in this table are used to assign the precedence for each incoming packet based on physical LAN port, TCP / UDP port number, and s

3.6.6 Anti-DoS "denial-of-service attack" (DoS Attack), a type of attack on a network that is designed to bring the network to its knees by

3.6.7 Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this

3.6.8 IPSec VPN (ADW-4401 only) The IPSec VPN (Virtual Private Network) feature in the ADW-4401v4 allows you to create a VPN connection between 2 ADW-

IPSec VPN Example In this example, 2 LANs are connected via IPSec VPN. Each end has an ADW-4401v4. Note • The LANs MUST use different IP address ran

IPSec Settings of ADW-4401 Site B: Step 1. Enable the VPN, it needs to take several minutes. Step 2. Enter a Name for this connection. Step 3. Ente

3.6.9 PPTP (ADW-4401 only) ADW-4401v4 incorporates a PPTP (Peer-to-Peer Tunneling Protocol) server which is compatible with the "VPN Adapter"

3.8.4 Diagnostic...

Windows PPTP Client Setup To connect to the PPTP (VPN) Server in the VPN Broadband Gateway: • The Microsoft VPN feature in the VPN Broadband Gateway

5. Click "Finish" to exit the Wizard. The new entry will now be listed in "Dial-up Networking". If necessary, you can change th

Windows 2000 Ensure you have logged on with Administrator rights before attempting this procedure. 1. Open "Network Connections", and start

4. On the screen below, enter the Domain Name or Internet IP address of ADW-4401v4 you wish to connect to. Click Next to continue. Windows 2000 VPN

6. Enter a suitable name, and click "Finish" to save and exit. Windows 2000 Finish Wizard Setup is now complete. To establish a connection

Windows XP Ensure you have logged on with Administrator rights before attempting this procedure. 1. Open Network Connections (Start-Settings-Network

4. Enter a suitable name for this connection. Click Next to continue. Windows XP Connection Name 5. On the screen below, select "Do not dial

7. Choose whether to allow this connection for everyone, or only for yourself, as required. Click Next to continue. Windows XP Connection Availabi

3.6.10 Other This function includes as following parts – IGMP Proxy, UPnP and Bridge. 3.6.10.1 IGMP Proxy IGMP Proxy enables the system to issue IGMP

3.6.10.2 UPnP UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity

1. Introduction The PLANET Wired / Wireless ADSL 2/2+ Router, the ADE-3400v3 / ADE-4400v3 / ADW-4401v4, provides office and residential users the idea

3.6.10.3 Bridge This page is used to configure the bridge parameters. Here you can change the settings or view some information on the bridge and its

3.7 Admin You can configure admin management in this part. It includes Remote Access, Commit / Reboot, Password, Backup / Restore, Update Firmware, Ti

3.7.2 Commit / Reboot The Comit / Reboot screen allows you to restart your router with its current settings or the factory default settings.  If yo

3.7.3 Password This page is used to set the account to access the web server of ADSL Router.The new password will be availability after system reboot.

3.7.4 Backup / Restore This page allows you to backup current settings to a file or restore the settings from the file which was saved previously. Ba

3.7.5 Upgrade Firmware You can upgrade the firmware of the router in this page. Make sure the firmware you want to use is on the local hard drive of t

3.7.6 Time Zone The system time is the time used by the device for scheduling services. You can manually set the time or connect to a NTP (Network Tim

3.7.7 System Log Click “System Log” to show the log information of device. The system log dialog allows you to view the system log and click the “Refr

3.7.8 SNMP This page is used to configure the SNMP protocol. You can set SNMP related information here. Read Community: Select to set the password fo

3.7.9 TR-069 (ADW-4401 only) This page is used to configure the TR-069 CPE. Here you may change the setting for the ACS's parameters.

Advanced Internet Functions  Virtual Servers This feature allows Internet users to access Internet servers on your LAN. The required setup is qui

3.7.10 ACL Access Control List Configuration If enabled, permits access to local management services from IP addresses contained in the Access Control

3.8 Diagnostic Your router is capable of testing your network and DSL connection. The individual tests are listed as Ping, ATM Loopback, ADSL and Diag

3.8.3 ADSL In this page, you can test the ADSL line tone status. Click “Go” to start testing. The test result will come out about 3 minutes later and

Appendix A: Glossary Address mask A bit mask select bits from an Internet address for subnet addressing. The mask is 32 bits long and selects the netw

DHCP (Dynamic Host Configuration Protocol) DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network.

Hop count A measure of distance between two points on the Internet. It is equivalent to the number of gateways that separate the source and destinatio

MIB Management Information Base - A collection of objects can be accessed via a network management protocol, such as SNMP and CMIP (Common Management

Route The path that network traffic takes from its source to its destination. The route a datagram may follow can include many gateways and many physi

Spoofing A method of fooling network end stations into believing that keep alive signals have come from and returned to the host. Polls are received a

independent requests, such as requesting a MIB value from an SNMP agent, in which first setting up a connection would take more time than sending the

1.2 Package Contents ‧ ADE-3400v3 / ADE-4400v3 / ADW-4401v4 Unit x 1 ‧ Power Adapter x 1 ‧ Quick Installation Guide x 1 ‧ User’s Manual CD x 1 ‧

Important Note According to Annex3 of the ERC/REC 70-03 publication, the use of Wideband Data Transmission systems has the following National Restrict

PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. T

PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. T

PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. T